HVAC Tools

FCTMS1

FCTMS1
Weight: 1.50 lbs

Jaws are hot drop-forged of carbon steel. Bends and flattens soft sheet metal up to 22 gauge. Straight handle model and higher leverage offset handle model. Heavy duty plastic grips for user comfort. (Left to right: FCT-M-S1 3" Straight, FCT-M-S2 3" Offset, FCT-M-S6 6" Straight).

Stock #	Nominal Length	Jaw Depth	Jaw Width	Bending Capacity*
FCT-M-S1 FCT-M-S2 FCT-M-S6	8.25" - 209mm 8.25" - 209mm 8.25" - 209mm	1.25" - 30mm 1.25" - 30mm 1.25" - 30mm	3.18" - 78mm 3.18" - 78mm 6" - 152mm	22 ga CR 22 ga CR 22 ga CR

FCTMS2

3" OFFSET SEAMER

FCTMS2
Weight: 1.50 lbs

FCTMS6

6" WIDTH STRAIGHT SEAMER

FCTMS6
Weight: 2.01 lbs

FCTMF1

FCTMF1
Weight: 1.40 lbs

FCT-M-F1 12-inch Folding Tool
FCT-M-F2 18-inch Folding Tool
FCT-M-F3 24-inch Folding Tool

Use wide folding depth side for 1-inch folds and opposite narrow depth side for 3/8 inch folds.

Stock #	Nominal Length	Fold Depth	Capacity*
FCT-M-F1	12" - 305mm	1" (25mm) or 3/8" (9.5mm)	24ga.CR/28ga. SS
FCT-M-F2	18" - 457mm	1" (25mm) or 3/8" (9.5mm)	24ga.CR/28ga. SS
FCT-M-F3	24" - 610mm	1" (25mm) or 3/8" (9.5mm)	24ga.CR/28ga. SS

FCTMF2

18" FOLDING TOOL

FCTMF2
Weight: 2.10 lbs

FCTMF3

FCTMF3
Weight: 1.10 lbs

2" FOLDING TOOL

FCT-M-F1 12-inch Folding Tool
FCT-M-F2 18-inch Folding Tool
FCT-M-F3 24-inch Folding Tool

Use wide folding depth side for 1-inch folds and opposite narrow depth side for 3/8 inch folds.

Stock #	Nominal Length	Fold Depth	Capacity*
FCT-M-F1	12" - 305mm	1" (25mm) or 3/8" (9.5mm)	24ga.CR/28ga. SS
FCT-M-F2	18" - 457mm	1" (25mm) or 3/8" (9.5mm)	24ga.CR/28ga. SS
FCT-M-F3	24" - 610mm	1" (25mm) or 3/8" (9.5mm)	24ga.CR/28ga. SS

FCTMC5

FCTMC5
Weight: 1.10 lbs

FCT-M-C5 Crimper blades (right) are 13 gauge cold-rolled steel heat-treated to a hardness of 45-50Rc. Crimps round and square duct, downspouts, etc. Compound leverage action. Heavy duty plastic grips for user comfort. FCT-M-C5S is a smaller version FCT-M-C5.

Stock #	Nominal Length	Throat Depth	Crimping Length*
FCT-M-C5	10" - 254mm	1.75" - 44.5mm	1.625" - 41mm
FCT-M-C5S	9.25" - 235mm	1.25" -32mm	1" - 25mm

FCTMC5S

FCTMC5S
Weight: 1.10 lbs

Stock #	Nominal Length	Throat Depth	Crimping Length*
FCT-M-C5	10" - 254mm	1.75" - 44.5mm	1.625" - 41mm
FCT-M-C5S	9.25" - 235mm	1.25" -32mm	1" - 25mm

FCTMN1

FCT-M-N1 Notcher blade (right) is hot drop-forged of carbon steel. Cuts 31 deg. "V"notch. Cuts clean without slippage. Compound leverage action. Heavy duty plastic grips for user comfort.

Stock #	Nominal Length	Throat Depth	Cutting Capacity*
FCT-M-N1	8" - 204mm	0.8125" - 20mm	22 ga CR

FCTMN1
Weight: 1.10 lbs

FCTML1

FCT-M-L1 Snap Lock Punch
Forged jaw punches impression on metal edge that fastens into opposite rolled metal edge for forming duct and pipe. Compund leverage handle action. Heavy duty plastic grips.

Stock #	Nominal Length	Throat Depth	Bending Capacity*
FCT-M-L1	8" - 203mm	3/8" - 9.5mm	24ga. CR

FCTML1
Weight: 1.10 lbs

FCTMT1

FCT-M-T1 Tension Tool
Handles all types of nylon ties including thin designs. Operate tension handles with one hand to tighten tie to desired tension. Use cutter handle to trim excess strap.

Stock #	Nominal Length
FCT-M-T1	8" - 203mm

FCTMT1
Weight: 1.10 lbs

FCTMD1

FCT-M-D1 Offset Duct Stretcher
Aligns and pulls ductwork together easing installation of drive cleats. Offset handle protects hand.

FCT-M-X1 Use to scribe a line or pierce and enlarge a hole in sheet metal duct.

Stock #	Nominal Length
FCT-M-D1	15.75" - 400mm
FCT-M-X1	13" - 330.2mm

FCTMD1
Weight: 1.10 lbs

FCTMX1

Stock #	Nominal Length
FCT-M-D1	15.75" - 400mm
FCT-M-X1	13" - 330.2mm

FCTMX1
Weight: 1.10 lbs

FCTMP1

FCT-M-P1 Pipe Duct Cutter (Double Cut)
3-blade tool cuts from center taking out 1/8" (3.175mm) track and leaving both edges clean.

Stock #	Nominal Length	Length of Cut
FCT-M-P1	10.5" - 266.7mm	1.25" - 31.75mm

FCTMP1
Weight: 1.10 lbs

FCTMH1

FCT-M-H1 The sheet metal hammer has a square face as well as a rounded chisel end, as well as a fiberglass handle and rubber grip.

Stock #	Nominal Length	Weight
FCT-M-H1	12 7/8"	18 oz.

FCTMH1
Weight: 1.10 lbs

FCTMA1

MCT-M-A1 Scratch Awl Marker marks metals, vinyl, wood, etc. The 3/12-in awl is drop-forged and heat treated for a long lasting marking point. It stores conveniently in the handle of all Midwest Snips aviation snips. Stock Number: FCT-M-A1 Nominal Length: 3/12 in. Weigth. 1/2 oz.

Stock #	Nominal Length	Weight
FCT-M-A1	3 1/2 in.	1/2 oz.

FCTMA1
Weight: 1.10 lbs

FCTMST1

FCT-M-ST1 & FCT-M-ST2 Forged Seamer Tongs: Jaws are hot-drop forged molybdenum alloy steel to provide exceptional strength. Cushioned handles for comfort and non-slip grip. Straight handle model and higher leverage offset handle model. (Left to right: FCT-M-ST1 straight, FCT-M-ST2 offset).

Stock #	Nominal Length	Jaw Depth	Jaw Width	Bending Cap.
FCT-M-ST1	9.75"- 248 mm	1.13 " - 29 mm	2.88 "- 73 mm	22 gs CR
FCT-M-ST2	9.50"- 241 mm	1.13 " - 29 mm	2.88 "- 73 mm	22 gs CR

FCTMST1
Weight: 1.75 lbs

FCTMST2

Stock #	Nominal Length	Jaw Depth	Jaw Width	Bending Cap.
FCT-M-ST1	9.75"- 248 mm	1.13 " - 29 mm	2.88 "- 73 mm	22 gs CR
FCT-M-ST2	9.50"- 241 mm	1.13 " - 29 mm	2.88 "- 73 mm	22 gs CR

FCTMST2
Weight: 1.75 lbs